WE43 Magnesium

Use slow-speed diamond saw or abrasive cut-off wheel designed for non-ferrous materials. Standard cut-off wheel (1.0-1.5 mm thickness) is appropriate. Use adequate coolant flow to prevent overheating and minimize deformation. The soft material requires gentle handling. Cutting speed: 150-250 RPM for most cut-off saws. Apply light to moderate pressure - the soft material requires gentle handling to avoid excessive deformation and work hardening. Avoid forcing the cut which can cause sample damage, work hardening, and significant deformation. Leave adequate allowance (~1-2 mm) for grinding away the heat-affected zone and any deformation from cutting.

Cold mounting with epoxy resin is preferred to avoid heat that could affect the microstructure. Use a low-shrinkage epoxy resin for best edge retention. Ensure complete cure before grinding to prevent edge rounding and maintain sample integrity.

Hot compression mounting is acceptable if the part tolerates ~150-180°C and moderate pressure (2000-3000 psi for phenolic). Use phenolic or epoxy-phenolic resins. Ensure proper cooling under pressure to minimize shrinkage. The material requires careful handling during mounting to avoid deformation. For critical applications, ensure the mounting material is compatible with the intended use environment.

The softness (75 HB) of WE43 Magnesium requires careful grinding. Use standard SiC grinding papers with adequate water lubrication. Disc speed: 200-300 RPM. Apply light to moderate pressure (20-30 N per 30 mm sample) - the soft material is prone to smearing if too much pressure is applied. Use sharp, fresh grinding papers to minimize deformation. Over-grinding can affect grain boundary revelation during etching. The work hardening behavior means strain-hardened material may show different grinding characteristics than annealed material.

Grinding sequence:

• 240 grit: Remove sectioning damage (20-40 seconds). Use moderate pressure to remove heat-affected zone.
• 320 grit: Remove previous scratches (20-40 seconds). Ensure complete scratch removal.
• 400 grit: Remove previous scratches (20-40 seconds). Ensure complete scratch removal.
• 600 grit: Remove previous scratches (20-40 seconds). Ensure complete scratch removal.

Always rotate the specimen holder 90° between steps to ensure complete scratch removal. Use complementary rotation (platen and holder same direction, different speeds) rather than contra-rotation to minimize deformation. Adequate water lubrication is critical - avoid drying during grinding which can cause smearing.

The softness requires careful polishing. Use diamond polishing with appropriate polishing pads for each stage. Apply light to moderate pressure throughout to prevent deformation. The work hardening behavior means strain-hardened material may show different polishing characteristics than annealed material.

Diamond polishing sequence:

• 6μm diamond: 2-4 minutes on a soft synthetic pad (e.g., TEXPAN) with light to moderate pressure (20-25 N per 30 mm sample). Start with 6μm to minimize damage. Monitor constantly for smearing and reduce pressure if any deformation is observed.
• 1μm diamond: 2-4 minutes on a soft synthetic pad (e.g., TEXPAN) with light pressure (15-20 N). Continue removing scratches from previous step.
• 0.05μm colloidal silica: 1-2 minutes on a soft final polishing pad (e.g., MICROPAD) with very light pressure. This removes any remaining fine scratches and prepares the surface for etching. Monitor for relief - reduce polishing time if excessive relief develops.

Use appropriate polishing lubricants. The soft material means polishing times should be sufficient but not excessive - avoid over-polishing which can cause relief and affect grain boundary revelation. Monitor the surface frequently under the microscope to check for smearing or excessive relief.

WE43 Magnesium responds well to standard etchants for magnesium alloy materials. The alpha magnesium with rare earth precipitates will reveal clearly with appropriate etchants. Glycol Etchant (Chemical Etching) - Standard etchant for this material:

• Application: Follow standard procedures for Glycol Etchant.
• Reveals: Grain boundaries and microstructure clearly.
• Rinse: Immediately with water, then ethanol. Dry with compressed air.
• Note: Use appropriate safety measures. Consult material-specific guidelines.

Etching Strategy:

• Start with Glycol Etchant for general microstructure examination
• Always clean and degrease before etching
• Use short initial etch times (a few seconds), check under the microscope, repeat if needed
• Check etching progress frequently - over-etching can obscure fine details

Safety: All etchants require proper PPE (gloves, safety glasses, lab coat), proper fume hood, and appropriate safety measures. Handle with care.